Quick answer
To replace a bearing plate assembly on a belt drive drum fan, first confirm your fan model and manufacture date match the compatible ranges, then disconnect power and remove the belt, pulley, and blade assembly before unbolting the old plate.
Why the bearing plate matters and when to replace it
The bearing plate assembly sits behind the fan struts and supports the shaft that carries the 6 in. pulley, belt, and blade assembly. When the bearing wears out, the shaft can wobble, causing noise, vibration, and uneven belt wear. Replacing the plate restores stable shaft rotation and prolongs the life of the pulley and belt.
Before ordering, verify your fan model and manufacture date. The bearing plate assembly is compatible only with steel 36 in., 42 in., or 48 in. belt drive drum fans. Specifically, it fits models beginning with BF36BD (manufactured after June 2008), BF42BD (manufactured after April 2005), and BF48BDC5. If your fan falls outside these ranges, this part will not fit. Check the model plate on your fan to confirm.
Tools and preparation
Gather the necessary tools: a socket set, wrench, screwdriver, and possibly a pulley puller. You will also need the replacement bearing plate assembly and a new belt if the old one shows wear. Work on a stable surface and have a container for small parts.
Always disconnect the fan from its power source before beginning any repair. This prevents accidental startup. If the fan is hardwired, turn off the circuit breaker and tag it to avoid someone restoring power while you work.
Bearing plate installation steps
- Step 1: Verify compatibility: Locate the fan's model plate and confirm it begins with BF36BD (manufactured after June 2008), BF42BD (manufactured after April 2005), or BF48BDC5. If the model or date does not match, do not proceed. Snap a photo of the model plate for future reference.
- Step 2: Disconnect power and remove the belt: Unplug the fan or turn off the breaker. Release tension on the belt by loosening the motor mount bolts, then slip the belt off the pulleys. Inspect the belt for cracks or glazing; replace it if worn.
- Step 3: Remove the pulley and blade assembly: Use a socket to remove the bolt securing the pulley to the shaft, then slide the pulley off. Next, remove the fan blade assembly by loosening the set screws on the hub and pulling it straight off the shaft. Mark the pulley orientation before removal to simplify reinstallation.
- Step 4: Unbolt the old bearing plate: Remove the bolts that secure the bearing plate to the fan housing or struts. Support the plate as you remove the last bolt to prevent it from dropping. Keep the bolts in a labeled bag; they may be reusable.
- Step 5: Install the new bearing plate: Position the new bearing plate behind the fan struts and align the bolt holes. Insert and tighten the bolts finger-tight first, then torque them in a crisscross pattern to avoid warping. Ensure the bearing is seated flush and spins freely before proceeding.
- Step 6: Reinstall the blade assembly and pulley: Slide the blade assembly onto the shaft and tighten the set screws. Reinstall the pulley and secure its bolt. Check that the shaft turns without binding. Spin the shaft by hand to confirm smooth rotation.
- Step 7: Reinstall the belt and tension it: Route the belt over the pulleys and adjust the motor mount to achieve proper tension—typically 1/2 inch of deflection at the midpoint. Tighten the motor bolts. Over-tensioning can damage bearings; under-tensioning causes slippage.
Product facts
- Bearing Plate Assembly for 36 - 48 in. Steel Belt Drive Drum Fans: This bearing plate installs behind the fan struts and facilitates the operation of the fan with a shaft for installing the 6 in. pulley, belt, and fan blade assembly. It is the mounting point that keeps the shaft aligned, so a worn plate directly causes wobble and belt misalignment.

Bearing Plate Assembly for 36 - 48 in. Steel Belt Drive Drum Fans - Bearing Plate Assembly for 36 - 48 in. Steel Belt Drive Drum Fans: For use only with our steel 36 in., 42 in., or 48 in. belt drive drum fans, and compatible with fan models beginning with BF36BD (manufactured after June 2008), BF42BD (manufactured after April 2005), and BF48BDC5. Confirm your model and date before ordering to avoid a part that will not fit.


